Astro Decoder Factory Reset
How does a factory reset exactly work in MAXWEST Astro 5S? Is it possible to recover data in MAXWEST Astro 5S after factory reset? I have forgotten the security password for my MAXWEST Astro 5S. What should I do? What should I do before performing a hard reset on MAXWEST Astro 5S? How will factory reset affect the SD card in MAXWEST Astro 5S?
Last updated16 March, 2015More information about CV59 - CV61More about CV59Effects modulation frequency of Mars and Gyra light. The lower the value the faster the frequency becomes. Factory set to 2Ehex, 46dec.More about CV60Effects time between light modulations for Mars and Gyra light.
Astro Decoder Factory Reset Password
The lower the value the less time between modulations. Try setting this to a value of 0Chex, 12dec for Mars light. It is factory set to 36hex, 54dec for Gyra light. Try experimenting with CV59 and CV60 to customize the look of the Mars or Gyra light. Mars and Gyra lighting cannot be operated simultaneously.More about CV61 optionsSetting bit 0 = 1 will re map function 0 rear headlight control to function 4 control.
Not applicable with version 16 and up decoders which use function re map.Setting bit 3 will enable headlight functions to remain on in analog mode even with analog mode not enabled (via bit 3 of CV29.) The advantage is when using straight DC voltage to make a stop block for control purpose, the lights will remain on when the loco is in the stop block.Setting bit 5 enables opposite dim. The headlight opposite the direction of travel comes on dim (50% power).Other notesWhen the decoder receives a broadcast stop signal the headlights will remain on in the direction they had before receiving the broadcast stop signal.Resetting CV'S to their factory defaultOn the programming track ONLY, write a value of two into CV8 or CV30. The decoder must go through a power off then power up, except the A1X, which will reset itself automatically.
CV'S will then reset to the factory default values on power up.Note: writing to CV8 does not actually change the value in CV8 because it is a read only register. When writing a two into CV8 it actually will write to CV30. This enables a factory reset with command stations that use physical register programming like the MRC 2000 and Atlas Commander.
CVs that will be reset to the factory default are: 1, 2, 3, 4, 5, 6, 17, 18, 19, 29, 30, 49,50, 61. The user loadable speed table is not effected by the reset to default values.Optional lighting effects for the head light and reverse light:. CV49 controls lighting effect and directional qualifier for forward headlight (White wire). CV50 controls lighting effect and directional qualifier for reverse light (Yellow wire).Use the following two tables to assign a lighting effect:Each CV uses two digits. The upper digit (MSB) is used as a directional qualifier. The lower digit (LSB) determines the lighting effect.
The numbers are Hexadecimal. Example for forward headlight: CV49=08hex, rule 17 applied. CV49=06 hex, rotary beacon on when loco going forward. CV49=14hex, single pulse strobe when loco reversed.Examples for reverse light: CV50=25hex, double pulse strobe on all the time. CV50=13hex, flashing light when loco reversed. Note: If your command station uses decimal numbers you will have to convert from hexadecimal to decimal.Motor TrimMotor trim allows the entire speed range of a decoder to be shifted up (faster) or down (slower) using CV 66 and CV 95.
This makes speed matching locomotives for consisting extremely easy. Also adjusting for notoriously fast or slow locomotives is simple. Motor trim can be used with 28/128 speed steps, User Loadable Speed Tables, and 3 point speed curves to adjust the entire range up or down.A value above 128 will increase the overall speed (the higher the number the faster the locomotive will go) and values below 128 will slow the locomotive (the lower the value the slower the locomotive will travel. The resolution (precision of the adjustment) of the values for motor trim is 4.
This means that for every 4 you add or subtract from the base trim value of 128 the speed will be adjusted by a percentage.RailcomRailCom is a standardized protocol for bi-directional communication between decoders and command stations on the OPERATIONS track. RailCom will allow you to read CV’s as well as request specific information from your operating locomotives like fuel and water levels. Railcom allows for signal systems, block detection, and computer automation. For more information check out the RailCom manual in the literature section of www.tcsdcc.com. Factory settings: CV49= 00hex, CV50= 10hex. Decimal equivalent: CV49=0, CV50=16. This default sets up auto reversing headlights.To remap yellow wire (FO) to button 1.
Astro Decoder Factory Reset Codes
Set CV34=4.To set up Blinking Ditch LightsGreen wire (F1) used for one ditch light. Violet wire (F2) used for other ditch light.Set: CV51=42 ditch light phase A CV52=43 ditch light phase BCV36= 4 remap violet wire to button 1Button 1 now turns off/on both lights. Then use button 2 or 5 to control blinking.To set up rotary beaconIf using a T4/T6 decoder, use brown wire (F3) to beacon. Set CV53=38.To set up manual control of headlightsWhite wire (F0) used for front head light. Set CV49=32.Yellow (F0) wire used for rear light.
Set CV50=32.To set up auto reversing headlightsSet CV49=0. Set CV50=16.To set up Gyra light for white wire headlight controlSet CV49=39, or for forwarddirectional qualifier set CV49=7.To set a light to manual non directionally qualified controlSet the required CV to 32. ');//-.
Maxwest Astro 5 Hard Reset: The recent year Maxwest Astro comes on the mobile market. The performance of the company is very good and they released many kinds of mobile on the market. The Maxwest Astro 5 is one of them; In 2014 December available released the mobile on the market.
The world most popular OS Android 4.4.2 KitKat operates the mobile very nice. All kind of network supported up to 3G HSPA 21.1/5.76 Mbps. The WLAN WiFi and hotspot that are most useable on the mobile and tablet user. Today we are going to learn Maxwest Astro 5 Hard Reset systems.
We are at this point how to factory reset Maxwest Astro 5 mobile. 3) Now you are able to face a new interface that is.
It’s your point; in this interface you are able to see a list of menu items.4) From the menu items you should select wife data/ factory reset and press power button for confirm it. Maxwest Astro 5 Hard reset5) On the next steps the android recovery option want form you conformation you want to factory reset your android device? If you select “ Yes” then all data will delete form your mobile.6) Wait some time work is running after done the factory reset the phone again show android recovery option; now you should select reboot the mobile via volume (+) or (-). After sleeting press power button and your android device is reboot now.7) All work is done!!! Now see your mobile is same as new cell phone. Setup step by step like just new android phone setup.